| Tool Type | Job Name | Tool Number | Tool Diameter | Cut Length | Speed (rpm) | Feed (inch/min) | Load Meter (%) | Time Cutting (minutes) |
|---|---|---|---|---|---|---|---|---|
| Carb Finishing | Oil Cooler Bracket | 4 | 1.000 | 20.200 | 520 | 2.080 | 21.0 | 00:09:43 |
| Face Mill | Oil Cooler Bracket | 5 | 3.000 | 32.400 | 573 | 9.170 | 92.6 | 00:03:32 |
| HSS Roughing Endmill | Oil Cooler Bracket | 3 | 0.750 | 35.900 | 365 | 2.800 | 6.4 | 00:12:49 |
| HSS Drill | Oil Cooler Bracket | 2 | 0.390 | 3.900 | 700 | 2.100 | 4.8 | 00:01:51 |
| Center Drill | Oil Cooler Bracket | 1 | 1.000 | 3.000 | 275 | 1.200 | 2.8 | 00:02:30 |
| Standard Tap | 57 | 8.300 | 155 | 1.750 | 13.7 | |||
| HSS Drill | 12 | 5.600 | 375 | 1.700 | 19.0 | 00:03:29 | ||
| Standard Tap | 57 | 7.400 | 167 | 1.880 | 14.7 | 00:00:00 | ||
| Carb Drill | 29 | 5.400 | 950 | 3.600 | 30.2 | 00:01:50 | ||
| HSS Drill | 19 | 9.600 | 270 | 1.400 | 15.7 | 00:06:51 | ||
| Standard Tap | 6 | 6.700 | 210 | 1.600 | 12.5 | 00:04:11 | ||
| Boring Bar | 24 | 30.100 | 660 | 8.200 | 27.9 | 00:03:40 | ||
| HSS Finishing Endmill | 8 | 14.200 | 280 | 2.200 | 7.5 | 00:06:27 | ||
| Face Mill | 33 | 450.650 | 480 | 20.800 | 70.7 | 00:21:40 | ||
| Spiral Tap | 56 | 14.670 | 135 | 1.880 | 14.7 | 00:07:48 | ||
| Boring Tool | 27 | 21.600 | 320 | 2.300 | 23.2 | 00:09:23 | ||
| Center Drill | 56 | 40.150 | 845 | 2.640 | 26.7 | 00:15:12 | ||
| Spiral Tap | 39 | 187.600 | 165 | 12.690 | 128.2 | 00:14:47 | ||
| Carb Drill | 14 | 108.000 | 650 | 2.990 | 30.2 | 00:36:07 | ||
| Standard Tap | 9 | 1.000 | 4.000 | 155 | 11.920 | 120.4 | 00:00:20 | |
| Carb Drill | 13 | 0.750 | 20.440 | 860 | 4.200 | 42.4 | 00:04:52 | |
| HSS Finishing | 15 | 2.000 | 15.600 | 210 | 2.400 | 24.2 | 00:06:30 | |
| Carb Counterboring Tool | 18 | 1.180 | 27.100 | 388 | 4.660 | 47.1 | 00:05:49 |